产品简介

XM PFP 多组分喷雾器

被动防火 (PFP) 设备

处理两部分环氧膨胀防火涂料

被动防火 (PFP) 涂层通过将结构钢从高温中隔离而使结构更具耐火性，从而购买时间疏散前结构崩溃。

Graco XM™ PFP 多组分喷雾器提供数据报告技术，因此您可以确认环氧膨胀涂层是否按照制造商设定的要求按比率喷涂。XM PFP 易于使用，保持一致的温度控制，并在 Graco XM PFP 上提供精确的比例计数，以实现精确的按比混合

处理 1:1 至 10:1 的两部分环氧膨胀防火涂层

提供精确的比例控制

如果发生断开比例情况，系统将自动停止

提供数据报告以验证材料是否正确应用

监控、跟踪和收集数据：混合比率、压力、温度、流量和材料使用

USB 端口可轻松下载数据报告

准确、按比率混合减少材料浪费

几乎消除了去除不正确混合材料 的困难任务，通过 “设置并忘记” 参数设置

XM PFP

美国

公制

混合比范围

1:1-10:1（以 0.01 为增量）

比公差范围（报警前）

+/-5%

最大流量（测量）含油)

每分钟 13.6 升

流体粘度范围

可处理装入加热罐中的乳胶材料，使用 RAM 喂入活塞泵

进气口

1 英寸不扩散（f）

流体进口

桶（饲料泵）

A 和 B 材料的最大流体工作压力

41 MPa，414 巴

英文介绍

XM PFP Plural-Component Sprayers

Passive fire protection (PFP) equipment

Handles two-part epoxy intumescent fireproofing coatings

Passive fire protection (PFP) coatings make structures more resistant to fire by insulating structural steel from high temperatures and as a result, buy time for the evacuation before structural collapse.

The Graco XM™ PFP Plural-Component Sprayer offers data reporting technology, so you can confirm that epoxy intumescent coatings are sprayed on-ratio, at requirements set by the manufacturer. The XM PFP is easy to use, maintains consistent temperature control and offers precise ratio contro Count on Graco XM PFP for accurate, on-ratio mixing

Handles two-part epoxy intumescent fire protection coatings from 1:1 to 10:1 Provides precise ratio control

If off-ratio conditions occur, the system will automatically stop

Offers data reporting for verification the material was properly applied

Monitors, tracks and collects data for: mix ratio, pressure, temperature, flow rates and material usage

USB port to easily download data reports

Accurate, on-ratio mixing reduces material waste

Virtually eliminates the difficult task of removing improperly mixed material Offers peace of mind with "set and forget" parameter settings

XM PFP

U.S.

Metric

Mix Ratio Range

1:1-10:1 (in 0.01 increments)

Ratio Tolerance Range (before alarm)

+/- 5%

Maximum Flow Rate (measured with oil)

13.6 liters per minute

Fluid Viscosity Range

Handles mastic materials which are loaded into heated tankswith ram-fed priming piston pumps

Air Inlet

1 in. npt(f)

Fluid Inlets

Pail (Feed Pumps)

Maximum Fluid Working Pressure for A and B Materials

41 MPa, 414 bar